Spinning Process of Staple Yarns and Filament Yarns

Mar 26, 2016 |

Staple Yarn Spinning and Filament Yarn Spinning

Staple Yarns

Staple or spun yarns in other hand are made from short length of fibers. It can be found from natural fibers or can be produced using synthetic as staple filament yarns. As it is short length, staple fibers need to be held together with others in order to get the long and continuous yarns.

Spinning staple yarns process is much complicated and requires several stages need to be done before Staple yarns can be produced. In terms of cost production, it is much higher compare with Filament yarns and this means a lot of energy consumption will be waste during this process.

Fibre -> Blow room process – > Carding -> Combing -> Drawing -> Roving – > Yarn

Blowroom

A process where the raw materials packed in bale forms(supplier) will be open and clean the impurities on the surface by using bale opener machine.

Carding

It’s the heart of spinning process. This is where the flock from bales will be open into individual fiber. Thus, it will ease to remove the excess impurities on the fiber surface. At this point, short fiber which not suitable for production in terms of length requirements will be eliminated.

Combing

This is a process where the yarn will be straightened again so that they are arranged in parallel manner. While at the same time, the remaining of short fiber will be eliminated completely from the longer staple fiber. By doing this, long-staple will produce stronger and smoother fabric which are highly demanded in the market.

Drawing

At this stage, it will be pulled the sliver lengthwise direction over each other. Thus, it will cause it to be stronger and thinner in production which is very important in evenness of the yarn. If there is any faults occur during process, it will still pass into the yarn. Most of manufacturer will use blending process where two or more different types of fibers will be blended to form a yarn. Common type of blend use is Cotton/Polyester combination, by doing this it will not only reduce the cost but also increase the performance.

Roving

This is the final stage where the preparatory steps for insertion of the twist. Enough twist is given to hold the fibers together but still has no tensile strength. The roving in bobbins is placed in spinning frame where it passes several sets of roller which running at high-speed to convert into yarn forms.

Several common systems used by the manufacturer in spinning industry for Staple yarns are

* Conventional Ring Spinning
* Air-jet Spinning
* Open-end or Rotor Spinning
* Vortex Spinning

Filament Yarns

These yarns are made from long, and continuous strands of fiber. Most of them from synthetic and only silk represents for natural fibers in filament. Several common systems used by the manufacturer in spinning industry for Filament yarns are

* Wet Spinning
* Dry Spinning
* Melt Spinning
* Bicomponent Spinning
* Biconstituent Spinning

Filament yarns spinning is simplest and least stages require compare with Staple yarns spinning. The molten polymer of synthetic will be inserted into a vessel, after few coloration’s have been done, the solution will be pushed out through the spinnerets to become filament yarns.

General Comparison between Filament and Staple Yarns Performance

Properties             Staple      Filament
Tenacity                Low          High
Elongation              Low          High 
Comfort                 High         Low

Tenacity & Elongation

As stated above in the table, Filament yarns have excellence properties compare with Staple yarns. But still, in terms of real production each of these yarns has their own high demands usage. Although Staple yarns seams have weakness in tenacity, overcoming can be done by increasing twist on the yarns and by blends it with synthetic fibers.

Comfort

In terms of fabric production, Staple yarns contribute high comfort by providing good absorbent and heat trapped. It is really important for country which has high moisture environments. Filaments on the other hand, seem fit for cold weather because of lack in terms of absorbent and heat trapped.

Both filament and staple yarns have their own advantages/disadvantages. Each of them is produced base on their end-use products such as fabrics, rope, and fishing yarns. Filament which majorly based on synthetic and some from natural sources, because it can be produced base on the needs in terms of its length(continuous or staple) and properties such as pre-choose coloration, alteration in physical and chemical structure have made it some advantages in production.

While for staple yarns, although it seems loss due to the length, staple still got some advantages in terms of strength which will make the yarns more stronger when the content of absorbency is higher, thus will make it suitable use for machine treatment(washing machine). Meanwhile, common technique used by the manufacturer to reduce the cost production of staple is by combining staple(cotton) with filament(polyester), at the same time it didn’t only reduce cost but also will overcome few weakness of staple yarns. Some of the new advancement have been made by researchers are like Spinning Nano Yarns, Air Jet Spinning and High Speed spinning machine.

Posted in: Textile Spinning

Comments are closed.